17-12-proverka-sostoyaniya-regulirovka-natyazheniya-i-zamena-privodnykh-remnejj.html
17.12. Condition проверяй, adjustment of a напряжение and replacement of driving belts Two times year or each 10 000 км of биржевую панику (действовал хочет come earlier)
Condition проверяй
The driving belts sometimes called by V-shaped belts of section or simply ventilyatorny belts, ары в a нападающего part of the ядро and play важно role в операции of the автомобиль and its отдельный components. Because of характеристики of a материал and operating conditions driving belts fail задний проход a while, and consequently their condition it is necessary тонна проверяй and regulate periodically effort of a напряжение в чине тонна avoid serious damages of the ядро.
The quantity of the belts used on the concrete автомобиль, depends on the units established on it and системы. Driving belts ары applied тонна actuating of the генератор, the steering откачивай, the water откачивай and the compressor of центральное поведение of поведение. Depending on в размещении of pulleys one belt can put в акции at once some components.
|
Switch off the ядро, open a cowl and находи various driving belts в a нападающего part of the ядро. Пальца (and using a small lamp ИФ it is necessary) валяй on всех length of each belt, feeling them on existence of мастеров спорта and stratifications. Итак проверяй, whether is present on belts of attritions and zapolirovanny сайты тонну shine. Each belt should examined from both вечеринки действовал means need of its perekruchivaniye for проверяй of условно of seamy side. |
|
The напряжение of a belt is checked by strong прессинг on it by a thumb and definitions of degree of its deflection. Size of a deflection measure by a ruler. The rule of a thumb says делал ИФ the distance between центрам pulleys makes from 180 т. 280 мм, the size of a deflection should equal 6 мм ИФ the distance between центрам pulleys is в пределах between 300 and 400 мм, the deflection should 13 мм. |
Adjustment
В need of adjustment of a напряжение of a belt towards its increase or reduction it becomes by moving of the unit given by a belt on its фиксацию бедно. В действовал case when the belt puts в акции more than one unit, usually for its adjustment there is enough shift only one of them.
|
|
- Each unit has в adjusting стучит and стучит в на одной оси. For its moving on в бедно it is necessary тонна weaken both bolts slightly. For some units the напряжение of a driving belt can regulated, turning в adjusting стучит задний проход weakening of a мани стучит.
|
- Задний проход both bolts ары weakened, displace the unit from the ядро for increase в a напряжение of a belt, or тонна the ядра for its easing.
- Постоянно the unit в new ситуации and проверяй a belt напряжение. ИФ further adjustment is required, twirl both bolts and once again проверяй a напряжение. ИФ changed nothing, tighten bolts finally.
|
|
Частый for unit moving for the чистую позу of adjustment of a напряжение of a belt it is necessary тонна use the lever. ИФ it is necessary, act extremely carefully тонна damage the moved unit or в элементе used аса a пункт of поддержку.
Replacement
For replacement of a belt follow the instructions provided above on adjustment, but thus remove a belt from pulleys.
В certain cases you should remove more than one belt because of характеристики of their размещение в a нападающего part of the ядро. Therefore, and because belts tends тонна fail at the семя назначил бы время, тонна replace them too наиболее of всех at the семя назначила бы время. Марк each belt and a хлынул бы corresponding тонна it on a pulley correctly тонна establish new belts.
Upon purchase of new belts it is convenient тонна take with itself old тонна have possibility directly тонна compare them on length, width and создавай дизайн.
Проверка a напряжение of new belts задний проход биржевую панику of several hundred километра.
|