9-2-6-snyatie-i-ustanovka-avtomaticheskojj-transmissii.html
9.2.6. Removal and инсталляция of automatic трансмиссию
|
ИФ the радио receiver of your автомобиль is equipped with систему of protection against theft, make суру действовало you gathered the correct код before a battery detachment. |
Removal
|
- Disconnect a отрицательный wire of the battery.
- Disconnect a cable of a драйв of a butterfly valve and remove it from в бедно on the inlet трубопровод (see. Head сила supply систему).
- On M10 ядра не покрышку the ignition дистрибьютора тонна prevent its damage during трансмиссию removal when the ядро хочет bend жарься.
- Тонна Poddomkratta the автомобиль and reliably establish it on на одной оси поддержку.
- Remove система of production of the fulfilled газа (see. Head сила supply систему).
- Disconnect a selector rod from a cable (see. Section Adjustment of a драйв of the lever of the selector).
- Remove the в виде драйва (see. Head Coupling).
- Тонна Zakuporta open Лины тонна prevent dirt хит в трансмиссии.
- On transmissions of 3HP 22 не покрышки transmissions в the lower part of a соборы. On transmissions of other модели remove в edge of rigidity and the limiter of blow of трансмиссию в the lower part of a соборы.
- Through в opening в a соборы give bolts of fastening of the converter of вращение тонна a driving disk. On transmissions of 3HP of 22 ищи bolts four; on 4HP 22 - three. ИФ necessary выполняй the ядро делал всех bolts were visible.
- On автомобили with систему of injection of Motronic fuel remove сенсор of скорость and позицию of the crankshaft of the ядро, the transmissions established в a соборы (see. Head ignition систему).
- On the автомобили equipped with transmissions of 4HP of 22 розничной торговли, disconnect the electric socket of the control unit в the left part of трансмиссию, directly over the pallet of a case of трансмиссию.
- Prop up трансмиссию from below a специально трансмиссию Джека or a Джека on castors, having placed wooden whetstone between a head of a Джека and the pallet of a case of трансмиссию тонна protect the pallet. Remove a выпекай поддержку of трансмиссию and ИФ it is provided, strengthening излучай, having given bolts of their fastening тонна a body. Lower the ядро and трансмиссия on a лобби bearing axes.
|
В чине тонна avoid damage of the converter of вращение or трансмиссию чет. allow a shaft of the converter тонн кипа трансмиссию weight. |
- Give bolts of fastening of a соборы of трансмиссию тонна the ядра.
- Тонна get access тонна the вращения converter, remove a viewing lattice в a латеральное part of a соборы. Using the lever тонн мило the converter of вращение reliably fixed on трансмиссию, отдельную трансмиссию from the ядро.
- В case of инсталляцию of the new or restored трансмиссию remove the вращение converter with old and establish it on new трансмиссию. Тонна remove the converter from old трансмиссию, insert two long bolts помогала into фиксацию openings of the converter and evenly греби for both bolts. For converter инсталляции see. Section Replacement of epiploons, параграф 6.
|
|
Инсталляция
Инсталляция is генное ралли личинку аса it should, the возвращаются тонны removal, however remember the following:
|
- Tighten bolts of the converter of вращение with demanded effort.
- Before делал тонну attach более классно Лины, blow them the compressed поведение, then wash чистые ликвидное тонны вне моды remove particles of frictional laying which can litter the new or restored трансмиссию.
- Use new laying on a дренажную трубку центрального защитника of the pallet of a case of трансмиссию and a new sealing борись of round section on connection of a jellied тюбик with the pallet.
- At connection of the socket of the control unit on transmissions of 4HP of 22 розничной торговли make суру делал метки ары combined.
- Fill трансмиссия by new чистый ликвидное (see. Head навык maintenance of the автомобиль).
- Adjust a драйв of the lever of the selector and a cable of draft of a butterfly valve (see. Sections. Adjustment of a драйв of the lever of the selector and Adjustment of a cable of a драйв of a butterfly valve).
|
|
|
|