Проверка and replacement of the центральное bearing. BMW the 5th E28 / E34 series (from 1981 т. 1993 of релиз)
Repair of BMW E28 and series E34 from 1981 т. 1993
1. Автомобили of the пожар BMW of 5-series
2. Ядро
3. Cooling система
4. Сила supply систему
5. Ignition система
6. Control системы of the ядро and decrease в toxicity of the fulfilled газа
7. Система of production of the fulfilled газа
8. Coupling
9. Справочник боксируй of gear shifting (RKPP) and automatic трансмиссия (AT)
10. Трансмиссия Лину
10.1. Генерал информатион
10.2. Removal and в виде драйва инсталляция
10.3. Проверка of work and replacement of the elastic coupling
10.4. Проверка and replacement of the центральное bearing
10.5. Проверка and replacement of kardanny hinges
10.6. Проверка and replacement of a лобби of the centering directing
10.7. Replacement of the висел бы of equal угольное скорости of the в виде драйва
10.8. Removal and инсталляция of силу shafts
10.9. Проверка and replacement of КОСЯКИ CV and their protective покрышки
10.10. Replacement of латеральное epiploons of a case of дифференциал
10.11. Removal and инсталляция of a casing of дифференциал
10.12. Replacement of в epiploon of a gear wheel
11. Проверили бы Steering and временное прекращение
12. Жердь систему
13. Body
14. Control body sizes
15. Heater and поведение conditioner
16. Система of onboard electric оборудование
17. Навык maintenance of the автомобиль
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and операция receptions
21. Система of onboard diagnostics - a principle of functioning and коды of malfunctions
 













10-4-proverka-i-zamena-centralnogo-podshipnika.html

10.4. Проверка and replacement of the центральное bearing

Проверка

The центральное bearing consists of the assembly of the мяч bearing surrounded with a rubber pillow. Bearing assembly напрессована but the жарься of нападающего section of the в виде драйва is fixed by a мани борись the Центральное bearing from both вечеринки is protected by dustproof caps, but water and dirt nevertheless can get тонна the bearing and destroy it. Заключение драйва vibrations can lead тонна a bearing exit вне моды of операцию. Carefully тонна экс-аминов the центральное bearing, it is necessary тонна remove the в виде драйва (see. Section Removal and в виде драйва инсталляцию). And on the contrary, each назначает время, removing the в виде драйва for any reason, use possibility тонна экс-аминов the bearing. Занимайся гимнастикой the bearing and проверяй, how freely it rotates. ИФ the bearing is turned hardly, or there is a feeling делало песок inside got, make replacement. Экс-амины rubber pillow. ИФ it cracked or wore вне моды, replace it.

Replacement

 ПРОИЗВОДИТЕЛЬНОСТЬ ЧИН

  1. Put landing метки on нападающего and жарься sections of the в виде драйва.
  2. Give screws and remove the tightening plug, then отдельный в виде драйва sections. Remove the rubber plug, a washer and the tightening plug from нападающего section of the в виде драйва.
  3. Проверка условно of the rubber plug of the shlitsevy coupling. ИФ it is torn or cracked, replace it.
  4. Remove a мани борись of the центральное bearing and a.
1 — the Ман борись
2 — the лодка
  1. By means of a стриптизера remove bearing assembly.
  1. At стриптизера инсталляцию on assembly of the центральное bearing make суру действовал it pulls together a nave; ИФ it pulls for в external борись of assembly, it can lead тонна a rupture of rubber then it is necessary тонна replace всех assembly of the bearing.
  1. ИФ it is required тонна replace the bearing or a поддержку, assembly should камыш автомобиля в a автомобиль care центр мастер-класс since dismantling and assembly of the bearing and a поддержку needs a выжимай.
  2. Make сура действовала the тихо is on kardanny тонна a shaft, then напрессуйте assembly of the центральное поддержка on a shaft действовала таким образом it appeared aflush with a.
  3. On модели with the в виде драйва equipped with shlitsevy sections, establish on нападающего section of a shaft the tightening plug, a washer and the rubber plug. Grease shlitsa a disulfide - molybdenum greasing, then collect the в виде драйва. Track correctness of combination of метки. Чет. tighten the tightening plug while finally чет. establish the в виде драйва.
  4. Establish the в виде драйва (see. Section Removal and в виде драйва инсталляцию).
  5. On модели with the в виде драйва without shlitsevy sections put специально blocking structure on a carving of a фиксацию стучит of the более мило of a crosspiece of the в виде драйва, then tighten a стучит with demanded effort.
  6. On модели with the shlitsevy в виде драйва tighten the tightening plug with demanded effort.


«on посыльного жарься
10.3. Проверка of work and replacement of the elastic coupling
on посыльного нападающего»
10.5. Проверка and replacement of kardanny hinges