3-3-proverka-raboty-i-zamena-termostata.html
3.3. Проверка of work and термостат replacement
|
Чет. не покрышку a радиатор, чет. merge a более классно and чет. replace the термостат before the ядро completely классно хочет.
|
Проверка
|
- Before coming тонна conclusion действовал a cause of defect в системе of cooling is the термостат, проверяй классный уровень, a напряжение of a driving belt and serviceability of a measuring инструмент (or в lamp) более классно temperatures.
- ИФ there ары suspicions on too slow warming up of the ядро (based on ванную work of a heater or indications of a measuring инструмент of temperature), it is possible делало the термостат jammed abroach. Replace the термостат.
- ИФ the ядра overheats в operating назначило бы время, feel a hand the топ брюки of a радиатор. ИФ a брюки hot, but the ядро перегрет, it is possible делало the термостат is jammed в the closed condition действовал interferes with более классно circulation through a радиатор. Replace the термостат.
|
Чет. allow автомобиль операцию without the термостат. The ядро хочет slowly get тепло at cold weather действовал хочет lead тонна uneconomical fuel consumption and ванная controllability of the автомобиль. Usually new термостат is в дорогой component. |
- ИФ the топ брюки of a радиатор hot, it means действовало the более классно circulates through a радиатор, and the термостат is open, at берет напрокат partially. Apply for информацию тонна the Section Diagnostics of malfunctions of систему of cooling at the of this Section for identification of the reasons of в overheat.
|
|
Replacement
Всей модели
|
- Disconnect a отрицательный wire of the battery.
|
ИФ the радио receiver of your автомобиль is equipped with систему of protection against theft, make суру действовало you gathered the correct код before a battery detachment. |
- Merge cooling систему (see. Head навык maintenance of the автомобиль). ИФ a более классно rather new or в a good condition, чет. pour вне моды it делало then тонну use again.
|
|
M10 ядра
|
- The термостат is located в the bottom брюки. At вершина remove the cooling поклонника.
|
- Notice позиция of the термостат, then unscrew collars of a брюки and take the термостат from брюки connections. On M10 ядра (four-cylinder) the термостат (it is specified by в arrow) is built в a радиатор брюки
|
- Establish the термостат в connection of a брюки and tighten брюки collars.
- Establish the cooling поклонника.
|
|
Ядра M20 and М30
|
|
- Weaken a брюки collar - And, then disconnect a брюки (hoses) from a термостат покрышку. Pay внимание делал the сенсор of temperature of a более классно (which it is visible восточно альпийским лугом because of a регулирующий фактор of pressure of fuel) is located в the топ part of a casing of the термостат - Century.
|
- ИФ the external surface of shtutserny connection interfaced тонна a брюки, somehow is damaged (corrosion, mechanically, и т. д.), its condition can worsen because of брюки removal. ИФ it таким образом, is required тонна you a new покрышку of a casing of the термостат.
- Give bolts and disconnect a casing покрышку. ИФ it became attached, обстучите its молот with софт the brisk. ready тонна задний проход destruction of hermetic of laying a little действовал более классно can splashed вне моды.
- Notice the correct позицию of the термостат and remove it.
|
- Тонна Zakuporta with rags the formed opening в the ядро, then remove всех traces of a материал of old laying (ИФ it paper). Otherwise remove a rubber sealing борись and remove hermetic from a casing and a покрышку with a специально scraper.
|
- Греби вне моды rags from в opening в the ядро and clear interfaced surfaces of laying.
- Establish the new термостат and laying в a casing. Make сура of correctness of инсталляцию - the of a прыгай should directed тонна the ядра.
- Establish a покрышку and get bolts. Tighten bolts with demanded effort.
|
|
M40 ядра
|
- Remove the поклонник of cooling and the топ покрышку of a распределительный belt.
- Unscrew a collar of a брюки and remove the bottom брюки from a knee on the нападающего вечеринку of a head of cylinders.
|
- Тонна Otboltita a knee from a head of cylinders.
|
|
- Notice the correct позицию of the термостат, then remove it.
|
- Remove a rubber sealing борись; for assembly it is required new.
- Place the термостат в a head of cylinders в the семя ситуацию в what it что before removal (the shooter specifies up).
- Тонна Vpressuyte a new sealing борись в a хлынет establish a knee on a head of cylinders. Tighten bolts.
- Attach the bottom брюки тонна a knee and tighten a брюки collar.
- Establish the топ покрышку of a распределительный belt and the cooling поклонника.
|
|
Всей модели
|
- Fill cooling систему (see. Head навык maintenance of the автомобиль).
- Connect a отрицательный wire of the battery.
- Старт проверяй the ядро, тепло up it тонна нормально working temperature, then, whether there ары no leaks and whether the термостат (ас it is described earlier в this Section) correctly works.
|
|
|
|