|
8-8-snyatie-osmotr-i-ustanovka-komponentov-scepleniya.html
8.8. Removal, survey and инсталляция of components of coupling Removal
Access тонна coupling is usually provided with трансмиссию removal, without removal of the ядро from the автомобиль. ИФ the ядро nevertheless has тонна removed for майора maintenance, it is necessary тонна use possibility and тонна проверяй coupling on existence of signs of wear, replacing вне моды worn components necessarily. The procedure described below assumes делал the ядро is в the автомобиль.
|
|
- Remove трансмиссия from the автомобиль, having used recommendations of Head the справочник боксируй of gear shifting (RKPP).
|
|
- For поддержка of a disk of coupling during removal insert the средство for centering of coupling or в old entrance shaft of трансмиссию into the middle of a basket of coupling.
|
|
|
- Attentively экс-амины a flywheel and выжимай a disk, looking for combination метки. ИФ those ары present, put them with a scraper or paint действовало выжимай the disk and a flywheel at assembly were established в the семя ситуацию relatively each other.
|
|
|
- Релиз bolts of fastening of a выжимай disk тонна a flywheel (ары specified by shooters), turning each of them gradually for назначает время. Чет. it on diagonals until хочет remove всех pressure of a прыгай.
|
- Grasp выжимай a disk and completely give bolts, then отдельным выжимай a disk and a conducted disk from a flywheel. Pay внимание, в what вечеринке the coupling disk is wound.
|
|
Survey
Usually, when there ары проблемы в coupling work, them it is possible тонны должности тонна wear of assembly of a conducted disk of coupling. However, it is necessary тонна проверяй at the семя назначает время and other components.
|
|
- Экс-амины a moss wheel (see. A part the Repair work which is камыш автомобиля вне моды without extraction of the ядро from the автомобиль).
|
|
- Проверка directing bearing on the of a cranked shaft. Make сура действовал it rotates smoothly and silently.
|
- ИФ the surface of contact of the bearing with entrance shaft of трансмиссию is damaged or вне моды worn, replace the bearing.
- By means of a стриптизера remove directing bearing.
|
|
- Establish the new bearing by means of a replaceable head and a молот.
|
|
|
- Экс-амины в overlay of a disk of coupling.
|
|
|
1 — the трусики - it wears вне моды at coupling work
2 —
Rivets - they мило a трусики, and can damage выжимай a disk or a flywheel ИФ хочет adjoin тонна their surfaces
3 - Inscriptions - «Flywheel side» (the вечеринка turned тонна a flywheel) or something similar |
- Проверка, whether there ары no traces of pollution by oil and the генерала signs of wear. ИФ the трусики is polluted or вне моды worn, replace a disk. Проверка palpation and thickness of a disk of coupling, then compare results тонна the sizes specified в the Size table and adjusting data at the of the менеджмент. ИФ the disk too thin or is deformed, replace it. Проверка, whether there ары no stirred-up rivets, curvatures, the мастера спорта, the broken springs or other obvious damages. Ас it что specified above, a coupling disk usually replace each назначил бы время when it remove therefore ИФ there аров any doubts concerning its condition, replace it better.
|
|
- Usually vyzhimny the bearing (1), replace at the семя назначил бы время with replacement of a disk of coupling. Remove the bearing from в entrance shaft.
|
- It is recommended тонна релиза a returnable прыгай (3), тонны remove the lever of switching off (2) and тонна экс-аминов deepening for a указание of a pusher of the executive cylinder. Инсталляция of the lever of switching off of coupling and the bearing make upside-down.
- Проверка a working surface of a выжимай disk. ИФ it has мастеров спорта, furrows, scratches, oil or colourless рекламного ролика from в overheat, or other damages, it is necessary тонна replace a disk. Put a planeness measuring инструмент тонна a surface and make сура действовал it flat.
|
|
- Проверка, whether there ары no stirred-up rivets or the deformed petals of a прыгай.
|
- ИФ there ары any signs of wear of a выжимай disk, replace it. It is recommended тонна take for a rule тонны replace всех components of coupling в collecting (a conducted disk, выжимай a disk and vyzhimny the bearing) or ИФ old components worked rather long назначает время.
|
|
Инсталляция
|
|
- Before инсталляция carefully clear working surfaces of a flywheel and a выжимай disk. Work with тезис components only чистое hands. Чет. allow oil or dirt хит on frictional surfaces of components of coupling.
- Place conducted and выжимай disks on a flywheel, холдинг-компания a conducted disk on a place by means of the средство for coupling centering. Track действовал the conducted disk что established correctly (new disks usually have «Flywheel side» marking - the вечеринка turned тонна a flywheel - or something similar). At инсталляция of в old выжимай disk make суру делал the метки of combination put earlier coincided.
- Tighten bolts of fastening of a выжимай disk тонна a flywheel only пальца, working around.
- ИФ it is личинку yet, establish the средство for coupling centering в the middle of a basket of coupling (see
в иллюстрации). Move a disk делал the средство appeared precisely on the центр and the entrance shaft of трансмиссию easily entered through a disk into directing bearing. ИФ a disk badly отцентрован, it хочет невозможных тонн establish трансмиссию.
- Tighten bolts of fastening of a выжимай disk тонна a flywheel gradually в занимайся гимнастикой, moving on diagonals тонна avoid деформацию of a выжимай disk, with demanded effort.
- Grease with high-temperature greasing всех internal surface of the vyzhimny bearing. Make сура действовал the interior of a lubricant хлынет is filled. Put greasing аса завивай on a сжимай гнездо, and on fork пальца.
- Establish трансмиссия, the executive cylinder and все earlier removed components.
|
|
|
|