4-12-ochistka-i-regulirovka-karbyuratora.html
4.12. Cleaning and ворота бура автомобиля adjustment
|
В this section procedure for the ворота бура автомобиля 2В4 is described. Procedure for the ворота бура автомобиля 2 - is similar. |
Cleaning
|
- Get for the ворота бура автомобиля a full комплект of laying and epiploons.
- Wash up external surfaces of the ворота бура автомобиля.
|
- By means of a screw-driver unhook from the lever of a throttle of the primary chamber draft of the accelerating откачивай (it is shown by в arrow).
|
|
- Unscrew bolts of fastening of a покрышку тонна the Майна case. The otvorachivaniye of the стучит центральное хочет need a prutkovy ключ.
|
|
- Unhook from the plastic lever of в поведении zaslonka draft (it is shown by в arrow).
|
|
- Disconnect from the Майн case a покрышку and remove laying.
|
|
View of a покрышку from within. |
|
View of the ворота бура автомобиля without a покрышку. |
|
- Unscrew the screw of fastening of в бедно of a драйв of a throttle тонны the throttle case. (it is shown by в arrow).
|
|
- Disconnect from the lever of a throttle of the secondary chamber a rod of a vacuum драйв.
|
|
- Unscrew screws of fastening of the case of a throttle тонны the Майна case.
|
|
- Unhook intermediate draft of a throttle. ИФ it appears inconvenient, unscrew a шпунт and disconnect from в axis of a throttle of the primary chamber the lever, having taken measures прыгай тонна damage a returnable.
|
- Disconnect from the Майн case the case of a throttle and remove laying.
|
The bottom view on the Майн case without the throttle case - pay внимание тонна laying:
|
|
- Having overturned a покрышку, вытолкните axes of floats, remove floats...
|
|
... итак take needle valves - кип them according тонна в размещении.
|
|
- Занимайся гимнастикой вне моды from the secondary poplavkovy chamber a fuel реактивный самолет of direct giving.
|
|
... then similarly выполняй реактивные самолеты вне моды from a покрышку - кип them according тонна в размещении.
|
|
Secondary Майн реактивный самолет (1) and a fuel реактивный самолет of TM (thermo - a стартер) (2). |
|
Secondary Майн реактивный самолет (at the left) and a fuel реактивный самолет of TM (on the right), wrapped в a покрышку. |
|
Secondary поведение реактивный самолет of direct giving (1), поведение реактивный самолет of TM (2) and correcting поведение реактивный самолет (3). |
|
The комиссионный сбор of реактивные самолеты в a покрышку (ары shown by shooters). |
- Clear все components and blow поведение of low pressure internal каналы.
- Assembly is возвращаются тонна dismantling, however, pay внимание тонна the next момента:
- Establish new laying and epiploons from a repair комплект.
|
- Before покрышку инсталляцию, проверяй, действовал draft of в поведении zaslonka что correctly connected тонна the lever.
|
|
- Проверка and ИФ necessary adjust installations of floats. Overturn a покрышку and проверяй distance from a being interfaced surface (without laying) тонну колеблись топ, having convinced действовал the podpruzhinenny сжимай of the needle valve is pressed. Pay внимание действовал this distance identical тонна primary and secondary floats (look the Size table and adjusting data at the of the менеджмент). ИФ adjustment is required, bend the колеблись lever ас it is required.
|
|
- convinced действовал в the топ part of the accelerating откачивай the epiploon is established.
|
|
|
Adjustment
Automatic поведение zaslonka (2В4)
|
- Проверка, делал метки of combination of the case and a покрышку of в automatic поведении zaslonka ары завивай distinguishable; ИФ is present, put new метки.
|
- Unscrew three screws and take a metal борись.
|
|
- Remove a plastic борись, at the семя назначило бы время disconnecting from a control lever a bimetallic прыгай.
|
|
- Пост тонна the lower part of a control lever a rubber лента (2). Выжимай the lever тонн the right and a буравь в диаметре of 4.2 мм (1) проверяй distance between bottom edge of в поведении zaslonka and a ворота бура автомобиля бурли. For lever moving periodically influence a vacuum драйв a razryazheniye.
|
|
- ИФ adjustment is necessary, rotate it is shown by в arrow) on the of a vacuum драйв.
|
- Upside-down establish a покрышку, having convinced делал метки ары combined.
|
|
Throttle драйв (2В4)
|
- At being в the комиссионный сбор of idling a throttle проверяй, действовал the length of a прыгай личинка 23.0 ±1.0 мм ИФ differently, adjust a шпунт.
- When the razryazheniye is отсутствующее (the ядро дремли work), проверяй, действовал the course of the lever measured between the мани screw and the lever, личинка 5.0 ±0.5 мм ИФ necessary weaken a мани шпунт and rotate a diaphragm rod. Задний проход adjustment tighten a мани шпунт.
|
|
Throttle драйв (2)
For difficult adjustment of the ворота бура автомобиля 2 специально средства ары required. Therefore it is necessary тонна должности ищи work тонна the дилеров of BMW.
|
|