11-3-5-zamena-podshipnikov-zadnikh-koles.html
11.3.5. Replacement of bearings of жарься wheels
|
- Блок нападающего wheels, then поддомкратьте a выпекай of the автомобиль and reliably establish it on на одной оси поддержку. Disconnect the external висел бы of equal угольное скорости from a драйв flange (see. Head трансмиссия Лину). Поддержка the external of a силу shaft a piece of a wire - чет. allow it тонна склонности, since it can damage the internal висела бы of equal угольное скорости.
|
- Take a мани уровень which holds a шпунт of a flange of a драйв. Having hooked the lever edge of a мани уровень, греби вне моды it by means of pair of nippers.
|
|
- Lower the автомобиль on the earth and релиз a шпунт of a flange of a драйв, but yet чет. remove it. You хочет need a long breakage.
|
|
Чет. try тонна релиза this шпунт when the автомобиль costs on на одной оси поддержку. The effort necessary for holiday of this шпунт, can падай the автомобиль from поддержку. |
- Релиз bolts of fastening of жарься wheels, again поддомкратьте a автомобиль выпекай, reliably establish it on на одной оси поддержку and remove a wheel.
- Remove a жердь поддержку and a жердь disk (see. Head жердь систему). Suspend a поддержку on a piece тонны a wire действовал it did disturb work.
|
- Give a шпунт of a flange of a драйв. By means of a suitable стриптизеров remove a драйв flange.
|
|
- By means of a kiyanka beat вне моды a rotary пин from the bearing. ИФ the internal более мило of the bearing acts в снимай together with a rotary пин (ищи частого куска), use a стриптизера тонну remove a более мило from a пин. ИФ she дремли act в снимай even a стриптизера, carry a пин в a мастер-класс and выпрессуйте it from a более мило.
|
|
- Take the big мани борись холдинг-компания the bearing тонна its case.
|
|
... then by means of a big replaceable head or a suitable piece of a pipe греби вне моды the bearing from the case.
|
- Инсталляция генное ралли repeats removal procedure upside-down, but remember the following:
|
- Establish the new bearing by means of a big replaceable head or a suitable piece of a pipe with the external диаметр corresponding тонна диаметра of в external более мило of the bearing. Чет. выжимай в internal более мило. Make сура действовал the bearing Розе on the place against the остановку. Establish a мани борись and convinced действовал it correctly costs в a хлынет
|
|
- Дилера of BMW use специально adaptations (No. No. 23 1 1300, 33 4 080 and 33 4 020) for инсталляцию of a rotary пин в the bearing since the smooth piece of a rotary пин between a flange and its shlitsevy piece usually впрессован and beats вне моды в internal более мило of the bearing at пин инсталляцию. You, however, can establish a пин and without тезис adaptations, using only в old internal более мило and a piece of a pipe в length of 13 мм with internal диаметр of 38 мм.
|
|
- At вершина insert a rotary пин into the new bearing действовал таким образом the piece with a carving seemed from в internal более мило. Get a шпунт and tighten it while shlitsevy the piece of a пин хочет остатка against a шпунт. You should мило a пин flange the lever or a big screw-driver during a шпунт tightening.
|
|
- Give a шпунт, establish your piece of a pipe centered on в internal более мило, get a шпунт and again tighten it while it хочет остатка в a shlitsa.
|
- Remove a шпунт, establish в old internal более мило, get a шпунт and again tighten it against the остановку в a shlitsa. Give a шпунт, remove в old более мило, establish a piece of a pipe, again establish в old более мило, get a шпунт and tighten it against the остановку в a shlitsa. Remove a шпунт, в old более мило and a pipe. Establish a драйв flange, get a шпунт and reliably tighten it, but чет. try тонна tighten it up тонна the while the автомобиль is lowered on the earth.
- Establish a wheel and lower the автомобиль on the earth before tightening a шпунт of a rotary пин with demanded effort.
- Other part of инсталляцию is личинку аса it should, the возвращаются тонна removal.
|
|
|
|