2-1-3-snyatie-i-ustanovka-kryshki-golovki-cilindrov.html
2.1.3. Removal and инсталляция of a покрышку of a head of cylinders
|
ИФ the радио receiver of your автомобиль is equipped with систему of protection against theft, make суру действовало you gathered the correct код before a battery detachment. |
Removal
|
- Disconnect a отрицательный wire of the battery.
- Disconnect a брюки сапуна from a покрышку of a head of cylinders.
- On M20 ядра отболтите remove a язык программирования БЭЙСИК проверили бы of the inlet трубопровод and ИФ is available, a проверили бы for сенсора of the ядро or the idling stabilizer (it is возможные, it is required тонна disconnect electric sockets of сенсора and the stabilizer).
- On M30 ядра disconnect the electric socket of a measuring инструмент of в поведении stream. Remove клипсы from electroconducting and take сюда aside.
- Where it is necessary on M30 ядра, disconnect hoses and shtutserny connections from a брюки of в inlet поведении Лину, then релиз a клипс and remove a брюки from the butterfly valve case. Give nuts of fastening of a casing of в поведении purifier and remove a casing together with a брюки and a measuring инструмент of в поведении stream.
- Give фиксация nuts and washers of a покрышку of a head of cylinders.
|
Размещение of bolts of a покрышку of a head of cylinders (ары specified by shooters) on four-cylinder M10 ядра. |
|
Размещение of bolts of a покрышку of a head of cylinders (ары specified by shooters) on six-cylinder M20 ядра. |
- Where it is necessary, disconnect a клипс or a покрышку of a wire of a spark plug from the screw of adjustment of a gap and put it aside. Usually there is no need of a detachment of wires of spark plugs.
- Не покрышка heads of cylinders and laying. Throw вне моды old laying. On M40 ядра не покрышку a cam-shaft.
|
- Не покрышка heads of cylinders the M40 ядро.
|
|
- Не покрышка a cam-shaft the M40 ядро.
|
|
- Remove laying of a покрышку of a head of cylinders from the M40 ядро.
|
- ИФ it is provided, remove semicircular consolidation from the valve on a нападающего part of a head of cylinders.
|
|
Инсталляция
|
- Using a scraper, remove всех traces of a материал of old laying from surfaces of a покрышку and a head of cylinders.
|
extremely careful тонна damage софта aluminum surfaces. On sale ары available, and there can useful, специально solvents for removal of laying. Задний проход the материал of laying is completely removed, surfaces of laying can cleared of greasing by means of a возвышайся moistened в suitable состоятельно. |
- ИФ it is provided, establish semicircular consolidation on the valve в a нападающего part of a head of cylinders, then put специально RTV hermetic for laying on connections between consolidation and the corresponding surface of laying of a покрышку of a head of cylinders.
|
Задний проход drawing of hermetic it is necessary тонна establish a покрышку of a head of cylinders and тонну tighten nuts within no more than ten minutes. |
- Establish a cam-shaft покрышку (M40 ядра), a покрышку of a head of cylinders and new laying. Get washers and nuts; reliably and exactly tighten nuts. Чет. draw them - they should tightened таким образом тонна prevent leakage of oil through laying, but is excessive тонна деформировано a покрышку.
- Other part of procedure of инсталляцию corresponds тонна removal upside-down.
|
|
|
|