2-2-15-ochistka-bloka-cilindrov.html
2.2.15. Cleaning of the блокируй of cylinders
|
The caps established в каналах of cooling of the блокируй, can taken hardly or even тонна taken at всех. |
|
- Take from the блокируй of cylinders of a cap. For this чистую позу with a молот and a punch strike в the блокируй on one вечеринку of a cap, big flat-nose pliers grasp for its other edge and греби вне моды.
- Remove with a scraper from the блокируй of cylinders всех traces of a материал of laying. very careful тонна leave on condensed surfaces of the tease or a dent.
- Remove покрышки of калорию редьки bearings and отдельный from покрышки and the блокируй of cylinders loose leaves of bearings. Отметку тонна which cylinder bearings belong and they were established в a покрышку or в the блокируй, and then put aside.
- Take from the блокируй всех caps of oil pipelines, Caps ары usually established very hardly - probably it is required тонна буравь them and тонна чистое openings a tap. At assembly of the ядро use new caps.
- ИФ the ядро is strongly polluted, it is necessary тонна посылай it for cleaning by steam в a mechanical мастер-класс.
- Задний проход блокируй возвращаются from a mechanical мастер-класс once again чистое openings and канал of oil pipelines. В the majority of магазины of autoaccessories there ары специально brushes. Wash каналы вне моды water while it хочет begin тонна follow чистые, carefully дренажную трубку the блокируй and grease всех otfrezerovanny surfaces with light anticorrosive oil. ИФ the compressed поведение is available, for acceleration of drying use it, and blow them всех openings and каналы of oil pipelines.
|
When using the compressed поведение protect eyes! |
- ИФ the блокируй is strongly polluted or polluted by dirt, the corresponding cleaning can личинку hot soap решение and a жестко brush. This work carry вне моды carefully and allocate for it назначил бы время enough. Irrespective of methods of cleaning convinced делал всех openings and каналы of oil pipelines ары cleaned very carefully, the блокируй is dried completely up and the processed surfaces ары covered with light oil.
|
- Carving openings в the блокируй for exact measurements of efforts of a tightening at assembly should cleaned. For removal of a rust, corrosion, a carving составное or dirt wrap в each opening a tap of the corresponding size. ИФ it is possible, clear задний проход this операцию of в opening of garbage the compressed поведение. convinced действовал терпкое - oil or other ликвидное can lead всех openings тонна действовал at a tightening of bolts because of hydraulic pressure the блокируй хочет burst. The занимайся гимнастикой now came тонны clear carvings of всех bolts. Pay внимание делал BMW recommends bolts of a head of cylinders and калорию редьки bearings тонна replace new.
|
- Establish покрышки of калорию редьки bearings and a hand tighten bolts.
- Задний проход drawing on condensing surfaces of a suitable составное establish them в the блокируй. Сура действовала they ары established plainly and against the остановку, differently there can a leak. For this чистую позу there ары специально средства, however, итак successfully it is possible тонны apply a лица head which can inserted into a cap, the расширение piece on 1/2 дюймы and a молот.
|
- Put on new caps of oil pipelines non-drying hermetic and wrap them в блокируй openings. convinced действовал they ары reliably tightened.
|
- ИФ the ядро is supposed тонна collected further, for preservation it в purity покрышке the блокируй with a big plastic package.
|
|
|
|