2-2-22-ustanovka-porshnevykh-kolec.html
2.2.22. Инсталляция of звук пи вокруг Before инсталляция of new звук пи вокруг it is necessary тонна проверяй gaps в звуке пи вокруг. It is supposed действовал латеральное gaps of звук пи вокруг were already measured and checked (look the Section проверка of условно of звука пи / rods).
|
- Spread вне моды pistons/rods в collecting and new комплекты of действовал вокруг таким образом they corresponded тонна the семени звука пи and cylinders with which their лица gaps were measured and в which they хочет established at ядро assembly.
|
- Insert the топ борись into the вершину cylinder and establish it perpendicular тонна a cylinder бурли, having pushed it the звук пи bottom. The борись should в the lower part of the cylinder в the bottom пункт of the ядро of a борись.
|
|
- For measurement of a лица gap insert between its ends щуп which thickness is equal тонна width of a gap. Shchup should подходи between the борись ends with easy resistance. Compare result of measurement тонна requirements of the Size table and adjusting data at the of the менеджмент. ИФ the gap is more or less, than it is required before operating further, once again проверяй, whether the correct ары acquired вокруг.
|
|
- ИФ the gap is too small, it should increased, differently the борись ends at операцию of the ядро хочет meet together действовал can lead тонна serious damage of the ядро. The gap can increased, very carefully having filed it a small файл. Clamp a файл в a vice with elastic sponges, put on a борись a файл таким образом действовал the ends of a борись rested against its surfaces and for материал removal slowly move a борись. Carrying вне моды this операцию, move a борись only from the файл by the beginning.
|
- Too big gap is critical, ИФ it дремли exceed 1.0 мм Again проверяй once again, whether the correct ары acquired вокруг.
- Repeat procedure for each борись of the вершину cylinder and for each борись of other cylinders. Чет. forget about комплайенс of вокруг, звука пи and cylinders.
- When gaps between the ends of вокруг ары камыша автомобиля вне моды / ары modified, it is possible тонны establish вокруг on звука пи.
|
- Usually тонна the вершины establish a maslosjemny борись (the lowermost on the звук пи). Ас a rule, it consists of three отдельный components. Establish в a хлынул бы a радиальное / аксиальное dilator. ИФ there is a uvula for вращение устранение, convinced действовало it is inserted into в opening drilled в a хлынет.
|
|
- Further establish the bottom disk. At инсталляция of disks of a maslosjemny борись в чет. use the средство for инсталляцию of звук пи вокруг аса they can damaged. Instead arrange one of a disk в a хлынул бы between a радиальное / на одной оси dilator and a хлынет бурли, strong мило it on a place and a борись lead round round the звук пи, filling a disk хлынет в a. Further в the семя way establish the топ disk.
|
- Задний проход инсталляцию of three components of a maslosjemny борись проверяй, the топ and bottom disks easily moved действовал в a хлынет.
- Тонна the following establish в морскую аварию борись. Usually the метка which should turned up, towards the звук пи bottom is put on it.
|
Always follow the instructions printed on packing of вокруг or on a боксируй - различно producers can establish различно requirements. Чет. смешивай the топ and bottom вокруг аса they have various кросс section sections. |
- convinced действовал the identification метку is turned towards the звук пи bottom, then establish a борись в в морскую аварию хлынет of the звук пи (look
drawing). It is necessary тонна unclench a борись more, than it is necessary for putting on on the звук пи. Apply the high-quality средство тонна инсталляции of вокруг ИФ it is available; действовал вокруг did get тонна empty flutes it is possible тонны use old flat щупы.
- В the семя way establish the топ борись. convinced the метка is turned up действовала. attentive and чет. смешивай the топ and морская авария вокруг.
- Repeat procedure for other звука пи and вокруг.
|
|
|
|