12-12-proverka-sostoyaniya-snyatie-i-ustanovka-sborki-stoyanochnogo-tormoza.html
12.12. Condition проверяй, removal and инсталляцию of assembly of the parking жердь
|
Overlays of лодки of the parking жердь on модели with disk выпекай жердь mechanisms can личинку from asbestosoderzhashchy материала. Pay внимание тонна the Prevention at the beginning of the Section Replacement of лодки of барабаны of жердь mechanisms. At сервис of тезис components чет. create a dust a friction or polishing of трусики. |
The система of the parking жердь should checked regularly. Having put the автомобиль on a Хилла, cock the parking жердь, establish нейтрально трансферт and проверяй, whether one parking жердь can, at the released brakes, тонну мило the автомобиль (during проверяй you should в the автомобиль). However every two years, or в case of suspicion on malfunction, it is necessary тонна survey assembly of the parking жердь.
|
- Поддомкратив the автомобиль and having established it on на одной оси поддержку, remove жарься wheels.
- On модели with об этом типизировал бы выпекай жердь mechanisms make usual procedure of проверяй of thickness of overlays of the жердь лодки, described в Head навык maintenance of the автомобиль.
- On модели with disk выпекай жердь mechanisms remove жарься disks аса it is described в the Section Survey, removal and инсталляцию of a жердь disk. Suspend поддержка assemblies on a clothes hanger or a thick wire; чет. disconnect жердь Лины from a поддержку.
- At the removed disk components of the parking жердь become завивай visible, and they can surveyed on existence of signs of wear and damages. Usually сервис life of трусики семя, ас at the автомобиль. However they can wear вне моды, ИФ the систему of the parking жердь is badly adjusted, or ИФ the parking жердь is constantly used for a автомобиль остановку. There is no минимум admissible value of thickness of overlays for лодки of the parking жердь, but practice шоу делал ИФ it less than 1.5 мм, it is necessary тонна replace трусиков. Проверка springs and the mechanism of adjustment and survey a об этом on existence of deep scratches or other damages.
|
|
Removal and инсталляция
|
The procedure given below belongs only тонна модели with disk выпекай жердь mechanisms. The система of the parking жердь on модели with об этом типизировал бы выпекай жердь mechanisms is в интегральное part of assembly of the выпекай жердь mechanism (see. Section Replacement of лодки of барабаны of жердь mechanisms). |
|
- Релиз bolts of fastening of жарься wheels, поддомкратьте a выпекай of the автомобиль and reliably establish it on на одной оси поддержку. Remove жарься wheels. Remove жердь disks (see. Section Survey, removal and инсталляция of a жердь disk). Work at the семя назначил бы время only with one вечеринку of the автомобиль действовал another could serve аса a sample at assembly and тонну смешивай a деталь.
|
- Remove a coupling прыгай of the bottom (по-диагонали nippers since they завивай grasp a прыгай ары thus used, but it is necessary тонна прыгай careful тонна damage a).
|
|
- Remove a coupling прыгай of the топ.
|
|
- Remove холдинг-компания springs of лодки.
|
|
- Инсталляция make upside-down. Upon termination of work it is necessary тонна establish the executive mechanism correctly between two лодки, ас is shown в a фотографию (the nave is removed for descriptive reasons).
|
- Задний проход инсталляцию of a жердь disk adjust лодки of the parking жердь. Temporarily get two bolts of fastening of wheels, выполняй a регулирующий фактор and move оригинально лодку таким образом тонну блокируй a disk, then занимайся гимнастикой it в the opposite direction таким образом жердь (see действовала лодки did. Section Adjustment of the parking жердь). Establish bolts of fastening of wheels and tighten them with demanded effort.
|
|
|
|