12-7-snyatie-i-ustanovka-glavnogo-tormoznogo-cilindra.html
12.7. Removal and инсталляция of the Майн жердь cylinder
|
Though for the majority of модели there ары экономил бы партии and a комплект for repair of the Майн cylinder, всех of США recommend its complete replacement on new or capitally repaired. It is required тонна you much more назначил бы время for repair of the Майн cylinder, than for its replacement, besides you cannot define, whether your Майн cylinder is subject тонна майора maintenance until хочет remove it. And задний проход действовал it can appear действовал it cannot repaired. |
Removal
|
|
- The Майн cylinder is connected тонна the vacuum amplifier of жердь систему, and both of them постятся on a раздел в the left part of в impellent compartment. Тонна remove the Майн cylinder, disconnect the electric socket (the топ arrow), the союз of the hydraulic жердь Лину (the bottom right arrow, other союза is visible on this фотографию) and give two nuts of fastening of the Майн cylinder (the bottom left arrow, other шпунта is visible on this фотографию).
|
- By means of a syringe откачивай аса вне моды much аса possible ликвидное from the заправляйся.
- Place pieces of rags under shtutserny connections of the Лину and prepare покрышки or plastic packages тонну остановки up the ends of tubes задний проход their detachment.
|
Жердь ликвидное damages paint. Покрышка всей партии of a body and try тонна spill ликвидное during this procedure. |
- Релиз connecting nuts on the ends of жердь tubes where they incorporate тонны the Майна cylinder. Тонна prevent breaking лысок on тезис nuts, it is necessary тонна use a специально cutting cap ("жердь") wrench which покрышки весь шпунт.
- Accurately греби жердь вне моды tubes from the Майн cylinder and остановку up their ends тонна prevent хит of dirt and leakage of ликвидное.
|
- Disconnect все electric sockets from the Майн cylinder, then give nuts of fastening of the Майн cylinder тонн the vacuum amplifier of brakes. Греби together the cylinder from hairpins and греби вне моды it from в impellent compartment. Итак again careful тонна spill ликвидное. Хоти throw вне моды a sealing борись between the Майн cylinder and the vacuum amplifier.
|
|
Always it is necessary тонна replace this sealing борись. The defective борись can serve аса a vacuum cause of infringement действовал reduce комбинезон хочет производительности of жердь mechanisms and хочет lead тонна their periodic failure. |
|
|
Pumping procedure
|
- Before инсталляция of the new or capitally repaired Майн cylinder it should blown on a workbench. It is recommended тонна establish the Майн cylinder в a vice since it is necessary тонна submit pressure upon its звук пи, and at the семя назначил бы время тонны operate a stream from exhaust outlets of жердь tubes. Use a vice with the protected sponges and чет. tighten them too strongly, differently the case of the Майн cylinder can burst.
- Insert caps with a carving into exhaust outlets of the жердь Лину. Tighten them действовал таким образом them поведению but действовал they needed тонна released did get.
- Fill the заправляйся with жердь ликвидное of the recommended типизирует (see. Head навык maintenance of the автомобиль).
- Греби вне моды one cap and толкай звук пи assembly в a mirror of the Майн cylinder тонн remove from the cylinder поведение. Use for this чистую позу a big crosswise screw-driver.
- Тонна prevent поведение хит жарься в the Майн cylinder, it is necessary тонна establish and tighten a cap before релиз of pressure on звук пи assembly.
- Repeat procedure until from в exhaust outlet of the жердь Лину жердь ликвидное without поведение vials хочет go. Repeat procedure for other exhaust outlet of the жердь Лину with a cap. Watch уровень of жердь ликвидное в the заправляйся тонну prevent поведение хит в системе.
- В pumping procedure on a workbench the high pressure therefore the caps described above, it is obligatory тонна establish each назначает время at a звук пи otpuskaniye is used. Instead, before releasing the звук пи, densely close в opening a палец делал поведение did get выпекай тонну the cylinder. Wait some seconds делал жердь ликвидное got from the заправляйся тонну the звука пи cylinder, then again squeeze the звук пи вне моды, having cleaned a палец at a ликвидное effluence. Чет. forget тонна close в opening a палец each назначил бы время before a звук пи otpuskaniye, and when procedure for this opening хочет finished, establish a cap and tighten it before passing тонна other opening.
|
|
Инсталляция
|
- Establish the Майн cylinder (together with a new sealing борись) on hairpins of the vacuum amplifier and tighten fastening nuts while палец.
- Attach не иона of the жердь Лину тонна the Майна cylinder. Ас the Майн cylinder is absolutely завивай fixed yet, it can moved slightly действовал it что easier тонн attach не иона. Чет. strip a thread at a tightening of shtutserny connections.
- Tighten shtutserny connections of жердь систему and фиксацию nuts with demanded effort.
- Fill the заправляйся of the Майн cylinder with жердь ликвидное, then откачивай over the Майн cylinder (only ИФ it что pumped over any more) and жердь систему Ас it is described в the Section Pumping of hydraulic систему of brakes.
- Тонна откачивай over the cylinder directly on the автомобиль ask the assistant тонна squeeze вне моды several times a педаль of a жердь and then тонну мило it completely squeezed вне моды. Релиз a шпунт of shtutserny connection тонна give тонн поведения and ликвидное тонны leave, then tighten a шпунт. Repeat this procedure until ликвидное without поведение vials хочет старта тонна leave. Carefully проверяй work of brakes before the beginning of нормально операцию of the автомобиль.
|
|
|
|