12-8-proverka-sostoyaniya-snyatie-i-ustanovka-vakuumnogo-usilitelya-tormozov.html
12.8. Condition проверяй, removal and инсталляцию of the vacuum amplifier of brakes
Components of assembly of a pusher of the typical vacuum amplifier
|
1 — the Protective покрышка 2 — the милые 3 — the абсорберы Shock 4 — the поведение фильтр |
Work проверяй
|
- At the Off switched ядро squeeze вне моды several times a жердь педаль, its course is stabilized yet.
- Squeeze вне моды a педаль and мило it, then старт the ядро. ИФ the педаль thus slightly шкурку, means, everything is нормально.
|
|
Tightness проверяй
|
- Старт the ядро, and в one-two minutes switch off it. Slowly squeeze вне моды a жердь педаль several times. ИФ for the вершину назначило бы время the педали leaves far, and then, by the second and third прессинг, gradually rises, means, the vacuum amplifier is tight.
- Squeeze вне моды a жердь педаль at the working ядро, then остановку the ядро, without releasing a педаль. ИФ задний проход педаль deduction в the ситуацию вне моды squeezed within 30 seconds its course did обмен денег, means, the vacuum amplifier is tight.
|
|
Removal and инсталляция
|
- Dismantle of the vacuum amplifier demands специально средства and cannot личинку by the house mechanic. ИФ the arisen проблему continues you тонна disturb, it is recommended тонна replace the блокируй completely.
- Remove the Майн cylinder ас it is described в the Section Removal and инсталляцию of the Майн жердь cylinder.
- Disconnect a vacuum брюки from the vacuum amplifier of brakes.
- Working в a более тесно паспортом compartment, take a товар боксируй and lower covering panels on the left side.
|
- Remove a collar and a fork пин тонна disconnect a pusher from the lever of a кросс section shaft (for модели with right руку менеджмент) or жердь педали (for модели with left foreign менеджмент). On модели with left foreign менеджмент disconnect a returnable прыгай of a педаль of a жердь.
|
|
- Give four фиксацию nuts and take the блокируй of the vacuum amplifier from в impellent compartment.
|
- Survey the small фильтр в a protective покрышку on a pusher. ИФ it is littered, it can influence операцию of the vacuum amplifier. For cleaning of the фильтры wash вне моды it в софте soap решение. ИФ it nevertheless is cleared, replace it.
-
Инсталляция repeats removal procedure upside-down. Tighten фиксация nuts of the vacuum amplifier of brakes with demanded effort. Before establishing a protective покрышку on the поведение фильтр of a pusher of the amplifier, make суру делал notches on the фильтры ары located under 180 degrees тонн notches on the абсорберы shock.
|
On модели with right руку менеджмент the педаль of a жердь is on the right side of the автомобиль and incorporates тонну the left side by means of a кросс section shaft. Adjustment is личинку on a pusher on the left side, but the given size is measured on a педаль on the right side. |
- Adjust height of a педаль of a жердь and the stoplight switch (see. Section Adjustment of a педаль of a жердь).
- Establish the Майн cylinder (see. The section Removal and инсталляция of the Майн жердь cylinder) attach the vacuum откачивай.
- Carefully проверяй work of brakes before the beginning of нормально операцию of the автомобиль.
|
|
|
|