Removal, installation and adjustment of a trunk lid / door of a back. BMW the 5th E28/E34 series (from 1981 to 1993 of release)
Repair of BMW E28 and series E34 from 1981 to 1993
1. Cars of the BMW brand of 5-series
2. Engine
3. Cooling system
4. Power supply system
5. Ignition system
6. Control systems of the engine and decrease in toxicity of the fulfilled gases
7. System of production of the fulfilled gases
8. Coupling
9. Manual box of gear shifting (RKPP) and automatic transmission (AT)
10. Transmission line
11. Steering and suspension bracket
12. Brake system
13. Body
13.1. Removal and front grille installation
13.2. Removal, installation and cowl adjustment
13.3. Removal and installation of bumpers
13.4. Removal and installation of the panel of an internal covering of doors
13.5. Removal, installation and door adjustment
13.6. Removal, installation and adjustment of a trunk lid / door of a back
13.7. Removal, installation and adjustment of a latch, cylinder of the lock and door handles
13.8. Removal and installation of glass of a door
13.9. Removal and installation of a window regulator of a door
13.10. Removal and installation of an external mirror
13.11. Removal and installation of casings of a steering column
13.12. Removal and installation of seats
13.13. Check of seat belts
13.14. Care of the car and coloring
14. Control body sizes
15. Heater and air conditioner
16. System of onboard electric equipment
17. Routine maintenance of the car
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and operation receptions
21. System of onboard diagnostics - a principle of functioning and codes of malfunctions
 








13-6-snyatie-ustanovka-i-regulirovka-kryshki-bagazhnika-dveri-zadka.html

13.6. Removal, installation and adjustment of a trunk lid / door of a back

Trunk lid

 PERFORMANCE ORDER

  1. Open a trunk lid and cover edges of a luggage compartment rags to protect the painted surfaces at cover removal.
  2. Disconnect all cables and the electric wires attached to a trunk lid which can prevent cover removal.
  1. Lead round bolts of loops, having marked т.о. their situation.
  1. Ask the assistant to support a cover, then give bolts of fastening of loops to a cover from both parties and remove it.
  2. Installation make upside-down. Combine bolts of fastening of loops to a cover with the labels put at removal.
  3. After installation close a cover and make sure that it flush with the next panels of a body. Vertical and horizontal adjustment is made by moving of bolts of loops in their cuts. Release bolts of loops, displace a cover and tighten bolts.
  1. The height of the closed trunk lid in relation to the next panels of a body can be changed, having released lock bolts (are specified by shooters)...

... and/or the drummer (are specified by shooters), having displaced the drummer and/or the lock and having tightened bolts.


If the radio receiver on your car is equipped with system of protection against theft, make sure that you gathered the correct code before disconnecting a battery wire. Apply for information in the Section System of protection of an audiosystem from theft and language of an instrument guard before a wire detachment.


If after wire accession on your instrument guard there were inscriptions not in that language which is necessary to you, address to the Section System of protection of an audiosystem from theft and language of an instrument guard where procedure of installation of the necessary language is described.

Back door

 PERFORMANCE ORDER

  1. Disconnect a negative wire of the battery.
  1. Open a door of a back and cover the back roof edge rags to protect the painted surfaces at removal of a door of a back. Glass can be removed separately, having disconnected conducting and having given fixing screws - ask the assistant to hold glass while you release screws.
  1. Remove an internal covering from a back door. Where it is necessary, remove a covering on door edge for access to fastenings of an emphasis.
  1. Disconnect conducting and washer tubes. On some models, probably, it is required to pull out conducting from a back rack, and only then to disconnect the socket.
  1. Ask the assistant to support a back door in open situation and disconnect an emphasis from both parties, having given fixing screws. Where it is necessary, pull out a fixing pin or a spring clip and remove an emphasis from the hinge.
  1. Emphasis fastening on a back door.
  1. Removal of a fixing hairpin for a detachment of the lower part of an emphasis of a door of a back.
  1. Mark with a pencil position of levers of loops on a back door.
  1. Give screws and remove a back door from levers of loops. You will need a face key or capture.
  1. Installation make upside-down, but make sure that all coincided put before a label. Check a back door that it was closed precisely on the center between back racks and its lock worked correctly.


«on page back
13.5. Removal, installation and door adjustment
on page forward»
13.7. Removal, installation and adjustment of a latch, cylinder of the lock and door handles