Removal and installation of assembly of a rack of a forward suspension bracket. BMW the 5th E28/E34 series (from 1981 to 1993 of release)
Repair of BMW E28 and series E34 from 1981 to 1993
1. Cars of the BMW brand of 5-series
2. Engine
3. Cooling system
4. Power supply system
5. Ignition system
6. Control systems of the engine and decrease in toxicity of the fulfilled gases
7. System of production of the fulfilled gases
8. Coupling
9. Manual box of gear shifting (RKPP) and automatic transmission (AT)
10. Transmission line
11. Steering and suspension bracket
11.1. Steering
11.2. Forward suspension bracket
11.2.1. General information
11.2.2. Removal and installation of the forward stabilizer
11.2.3. Survey, removal, installation and replacement of plugs of the lever of a suspension bracket and basic levers
11.2.4. Removal and installation of assembly of a rack of a forward suspension bracket
11.2.5. Rack or shock-absorber replacement / twisted spring
11.2.6. Check and replacement of spherical support
11.2.7. Removal and installation of assembly of a forward nave and bearing
11.2.8. Diagnostics of malfunctions of a forward suspension bracket
11.3. Suspension bracket of back wheels
12. Brake system
13. Body
14. Control body sizes
15. Heater and air conditioner
16. System of onboard electric equipment
17. Routine maintenance of the car
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and operation receptions
21. System of onboard diagnostics - a principle of functioning and codes of malfunctions
 






11-2-4-snyatie-i-ustanovka-sborki-stojjki-perednejj-podveski.html

11.2.4. Removal and installation of assembly of a rack of a forward suspension bracket

Removal

Though assemblies of racks of a suspension bracket not always fail at the same time, replace the left and right are resistant in pair to prevent possible violations of controllability or a car course.


 PERFORMANCE ORDER

  1. Release, but do not remove bolts of fastening of forward wheels.
  2. To Poddomkratta a front of the car and reliably establish it on axial support.
  3. Remove a forward wheel.
  4. Disconnect all brake hoses and the electric wires going to the case of a rack of a suspension bracket.
  5. Disconnect electric sockets from ABS system if that is available.
  6. If you remove the left rack, disconnect the electric socket from the sensor of wear of brake shoes.
  7. Give a bolt of fastening of the wheel ABS sensor if it is available. Remove a brake disk (see. Head Brake system).
  1. Give these three bolts (are specified by shooters), and remove a mudguard of the brake mechanism.
  1. Disconnect a link of a bar of the stabilizer from the rack case (see. Section Removal and installation of the forward stabilizer).
  2. Give bolts of fastening of the rotary lever to the rack case.
  3. Pull out the lower part of the case of a rack so to provide access to the end of the rotary lever.
  1. Prop up a rack and give three fixing nuts in the top part of the rack located in an impellent compartment, then remove a rack.
  1. Remove rack assembly. If it is necessary to replace a rack (or the boss of the shock-absorber), see. Section rack or shock-absorber Replacement / twisted spring.

Installation

Installation make upside-down. Make sure that the uvula on the rotary lever coincides with dredging in the rack case.

The BMW firm recommends to use special greasing for a carving on bolts of fastening of the rotary lever. For all models tighten fixture with demanded effort.

Upon termination of work check corners of installation of forward wheels in dealer office of service or a repair truck, and if necessary adjust them.

«on page back
11.2.3. Survey, removal, installation and replacement of plugs of the lever of a suspension bracket and basic levers		 on page forward»
11.2.5. Rack or shock-absorber replacement / twisted spring