Replacement of a cable (cables) of a drive of the parking brake. BMW the 5th E28/E34 series (from 1981 to 1993 of release)
Repair of BMW E28 and series E34 from 1981 to 1993
1. Cars of the BMW brand of 5-series
2. Engine
3. Cooling system
4. Power supply system
5. Ignition system
6. Control systems of the engine and decrease in toxicity of the fulfilled gases
7. System of production of the fulfilled gases
8. Coupling
9. Manual box of gear shifting (RKPP) and automatic transmission (AT)
10. Transmission line
11. Steering and suspension bracket
12. Brake system
12.1. General information
12.2. General information on anti-blocking brake system
12.3. Replacement of blocks of disk brake mechanisms
12.4. Removal, major maintenance and installation of a support of the disk brake mechanism
12.5. Survey, removal and installation of a brake disk
12.6. Replacement of boots of drums of brake mechanisms
12.7. Removal and installation of the main brake cylinder
12.8. Condition check, removal and installation of the vacuum amplifier of brakes
12.9. Description, removal and installation of the vacuum hydraulic booster of brake system
12.10. Replacement of a cable (cables) of a drive of the parking brake
12.11. Adjustment of the parking brake
12.12. Condition check, removal and installation of assembly of the parking brake
12.13. Adjustment of a pedal of a brake
12.14. Check and adjustment of the switch of a stoplight
12.15. Survey and replacement of brake lines and hoses of hydraulic system of brakes
12.16. Pumping of hydraulic system of brakes
12.17. Diagnostics of malfunctions of brake system
13. Body
14. Control body sizes
15. Heater and air conditioner
16. System of onboard electric equipment
17. Routine maintenance of the car
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and operation receptions
21. System of onboard diagnostics - a principle of functioning and codes of malfunctions
 








12-10-zamena-trosa-trosov-privoda-stoyanochnogo-tormoza.html

12.10. Replacement of a cable (cables) of a drive of the parking brake

 PERFORMANCE ORDER

  1. Unbend a cover at the basis of the lever of the parking brake and give a nut of adjustment of a cable of the parking brake which also holds a cable on the brake lever (both are specified by shooters). There are two cables - on one on each back wheel - and nuts for each cable. On some models to get access to these nuts, it is necessary to remove completely central console.
  1. To Poddomkratta the car and reliably establish it on axial support.
  2. Remove a drum (see. The section Replacement of boots of drums of brake mechanisms) or a disk (see. Section Survey, removal and installation of a brake disk) back brake mechanism.
  1. On models with back drum-type brake mechanisms unhook a cable of the parking brake from the lever on a boot of a back brake (see. Section Replacement of boots of drums of brake mechanisms). On models with back disk brake mechanisms remove boots of the parking brake and the executive mechanism (see. The section condition Check, removal and installation of assembly of the parking brake) also unhook a cable of the parking brake from the executive mechanism. For this purpose pull for an external cam and disconnect it from an internal cam

... then pull out a finger holding a cable on an internal cam and remove an internal cam

  1. On models with back drum-type brake mechanisms pull out a cable and its cover from the back party of a board of a brake, then release a cable cover from clips on the back party of the longitudinal lever (easier to pull out an old cable and to insert new at the straightened cover, than at braided). On models with back disk brake mechanisms there is no need to disconnect a cable cover from a brake board, but for convenience it is better to release it from clips and directing to reduce its bends.
  1. Pull out a cable from a cover from a wheel.
  1. Grease a new cable with universal greasing, then insert it into a cover and push through so that its end left at the lever of the parking brake.
  2. Push a cable cover through a board of a brake and attach the back end of a cable to the lever of the parking brake (for models with back drum-type brake mechanisms) or to the executive mechanism (for models with back disk brake mechanisms). Make sure that you did not overwind a cable during its connection.
  3. Establish a cable cover back in clips from a reverse side of the longitudinal lever.
  4. On models with back drum-type brake mechanisms establish brake boots and a drum (see. Section Replacement of boots of drums of brake mechanisms). On models with back disk brake mechanisms establish boots of the parking brake and the executive mechanism (see. The section condition Check, removal and installation of assembly of the parking brake), and also a back brake disk (see. Section Survey, removal and installation of a brake disk).
  5. Lower the car on the earth and establish an adjusting nut on the lever of the parking brake. Adjust a cable of the parking brake (see. The section Adjustment of the parking brake) also establish a cover of the lever of a brake.


«on page back
12.9. Description, removal and installation of the vacuum hydraulic booster of brake system
on page forward»
12.11. Adjustment of the parking brake