Removal and carburetor installation. BMW the 5th E28/E34 series (from 1981 to 1993 of release)
Repair of BMW E28 and series E34 from 1981 to 1993
1. Cars of the BMW brand of 5-series
2. Engine
3. Cooling system
4. Power supply system
4.1. General information
4.2. Pressure removal in system of injection of fuel
4.3. Check of pressure of fuel / fuel pump
4.4. Removal and installation of the fuel pump, intermediate pump and fuel level sensor
4.5. Repair and replacement of fuel lines and connectors
4.6. Removal and installation of a fuel tank
4.7. General information about cleaning and repair of a fuel tank
4.8. Removal and air purifier installation
4.9. Check, adjustment and replacement of a cable of an accelerator
4.10. General information about the carburetor
4.11. Removal and carburetor installation
4.12. Cleaning and carburetor adjustment
4.13. General information about fuel injection
4.14. Systems of injection of fuel
4.15. Check of functioning of system of injection of fuel
4.16. Functioning check, removal and installation of a measuring instrument of a stream of air
4.17. Functioning check, removal and installation of the case of a throttle
4.18. Check of functioning and replacement of a regulator of pressure of fuel
4.19. Check of functioning and replacement of an injector of cold start and temperature switch
4.20. Check of functioning and replacement of fuel injectors
4.21. Functioning check, adjustment and replacement of the air valve of stabilization of idling
4.22. Search of malfunctions of system of injection of fuel
4.23. Diagnostics of malfunctions of a power supply system
5. Ignition system
6. Control systems of the engine and decrease in toxicity of the fulfilled gases
7. System of production of the fulfilled gases
8. Coupling
9. Manual box of gear shifting (RKPP) and automatic transmission (AT)
10. Transmission line
11. Steering and suspension bracket
12. Brake system
13. Body
14. Control body sizes
15. Heater and air conditioner
16. System of onboard electric equipment
17. Routine maintenance of the car
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and operation receptions
21. System of onboard diagnostics - a principle of functioning and codes of malfunctions
 






Взято с soccerinlife.com







4-11-snyatie-i-ustanovka-karbyuratora.html

4.11. Removal and carburetor installation

Removal

 PERFORMANCE ORDER

  1. Remove an air purifier as it is described in the Section Removal and air purifier installation.
  2. Disconnect from the carburetor an accelerator cable, having addressed to the Section Check, adjustment and replacement of a cable of an accelerator.
  3. On models with automatic transmission disconnect a dumping cable.
  4. Disconnect from the wire carburetor, remembering their arrangement.
  1. Unscrew the screw and disconnect from an arm of a drive of a throttle a wire to the case (it is shown by an arrow).
  1. Disconnect vacuum hoses, having paid attention that the hose with a white strip is attached to a white plastic tee, and vacuum hoses of the distributor of ignition approach to lateral faces of the carburetor.
  1. On the carburetor 2В4 disconnect and muffle hoses of system the coolings going from the TM valve (thermo - a starter).
  1. Disconnect hoses of supply of fuel.
  1. Unscrew four bolts and disconnect from (flange) isolating the screw on the inlet pipeline of the carburetor.
  1. If necessary unscrew nuts and remove from the inlet pipeline isolating flange.

Installation

Installation is return to removal, however, carefully clear being interfaced surfaces. The isolating flange allows a reuse if it is in a good condition. Adjust according to the Section Check, adjustment and replacement of a cable of an accelerator a cable of an accelerator and a dumping cable (where it is applied) - according to Head Automatic transmission (AT).


«on page back
4.10. General information about the carburetor
on page forward»
4.12. Cleaning and carburetor adjustment