Pressure removal in system of injection of fuel. BMW the 5th E28/E34 series (from 1981 to 1993 of release)
Repair of BMW E28 and series E34 from 1981 to 1993
1. Cars of the BMW brand of 5-series
2. Engine
3. Cooling system
4. Power supply system
4.1. General information
4.2. Pressure removal in system of injection of fuel
4.3. Check of pressure of fuel / fuel pump
4.4. Removal and installation of the fuel pump, intermediate pump and fuel level sensor
4.5. Repair and replacement of fuel lines and connectors
4.6. Removal and installation of a fuel tank
4.7. General information about cleaning and repair of a fuel tank
4.8. Removal and air purifier installation
4.9. Check, adjustment and replacement of a cable of an accelerator
4.10. General information about the carburetor
4.11. Removal and carburetor installation
4.12. Cleaning and carburetor adjustment
4.13. General information about fuel injection
4.14. Systems of injection of fuel
4.15. Check of functioning of system of injection of fuel
4.16. Functioning check, removal and installation of a measuring instrument of a stream of air
4.17. Functioning check, removal and installation of the case of a throttle
4.18. Check of functioning and replacement of a regulator of pressure of fuel
4.19. Check of functioning and replacement of an injector of cold start and temperature switch
4.20. Check of functioning and replacement of fuel injectors
4.21. Functioning check, adjustment and replacement of the air valve of stabilization of idling
4.22. Search of malfunctions of system of injection of fuel
4.23. Diagnostics of malfunctions of a power supply system
5. Ignition system
6. Control systems of the engine and decrease in toxicity of the fulfilled gases
7. System of production of the fulfilled gases
8. Coupling
9. Manual box of gear shifting (RKPP) and automatic transmission (AT)
10. Transmission line
11. Steering and suspension bracket
12. Brake system
13. Body
14. Control body sizes
15. Heater and air conditioner
16. System of onboard electric equipment
17. Routine maintenance of the car
18. Size table and adjusting data
19. Schematic electric circuits
20. Governing bodies and operation receptions
21. System of onboard diagnostics - a principle of functioning and codes of malfunctions
 








4-2-snyatie-davleniya-v-sisteme-vpryska-topliva.html

4.2. Pressure removal in system of injection of fuel

Fuel is extremely inflammable, therefore, working with any part of fuel system, accept additional precautionary measures. Do not smoke and do not allow emergence of open fire or lamps without plafonds near a working zone. Also do not work in garage where the equipment on natural gas with a match is applied.


 PERFORMANCE ORDER

  1. Take from the panel of safety locks a safety lock of a chain of the fuel pump.

If on a cover of the panel of safety locks there is no information on an exact arrangement of a safety lock of the fuel pump, address to the management on the car.

  1. Start the engine and wait, while it will not stop. Switch off ignition.
  2. Uncover a jellied mouth to remove pressure in a fuel tank.
  3. Now pressure in fuel system is removed.

To prevent hit of the remains of fuel on the engine, before a detachment of fuel lines spread out round them rags.


  1. Before work with any part of system disconnect from the storage battery a negative wire.

If the radio receiver on your car is equipped with system of protection against abduction, before a detachment of the storage battery be convinced that the correct code of reduction of system in action is known. Before a detachment of a wire address to the Section System of protection of an audiosystem from theft and language of an instrument guard.


If after connection of the battery on the display of the control panel there will be a message in other language, for procedure of installation of language address to the Section System of protection of an audiosystem from theft and language of an instrument guard.



«on page back
4.1. General information
on page forward»
4.3. Check of pressure of fuel / fuel pump